If you have any questions, contact the manufacturer or a qualified dealer. ! SAFETY FIRST ! Before using this equipment, read and follow these manufacturer’s instructions carefully. Press must ONLY apply pressure to the limbs in this area. ! IMPORTANT PRESS ! ! INFORMATION ! Certain bow models require the use of fixed stops to prevent the press forces from pushing the bow out of the bottom of the press Bow press MUST only be applied to the outer 2” of limb tips. Traditional style presses that use rollers to apply pressure only to the mid section of the limbs CANNOT BE USED. ! IMPORTANT PRESS ! ! INFORMATION ! Due to the innovative and advanced design of your Bear Archery bow limbs, it is of the utmost importance that your bow ONLY BE PRESSED IN PROPER BOW PRESSES. For this reason, we ask you read the Care and Maintenance section carefully to learn how easy it is to maintain the quality, performance, and level of satisfaction you expect from a Bear Archery product. We know how much you are going to enjoy your new bow. ![]() No other bow delivers a higher performance to value ratio than a Bear. It has been engineered for accuracy, long life, and built with quality and pride. When carried out properly, you will replace your string successfully, as though you had a professional archery shop do it for you.2013 Owner’s Manual Members of the ATA 817 Maxwell Avenue Ĭontents Important Bow Information 3-5 Archery Safety & Warnings 6-7 Bow Diagrams 8-10 Care & Maintenance 11-12 Bow/Cam Adjustments 13-30 Initial Bow Setup 32-36 Arrow Selection Information Warranties 37 38-39 Record important bow information here and keep for future reference.Ĭongratulations! Your new Bear Archery compound bow is the finest available. Step 8: Use the Allen wrench to tighten the limb bolts.The above are the simple eight steps that you need to restring your bow without using a press. Step 7: Take out the bowstring you want to replace from the fittings, then lower your compound bow. Start pulling on the bow’s riser and don’t stop until your bow attains its “full draw” position. Step 6 : With both feet, step on the replacement bow string. The grooves are part of the bowstring fittings. Step 5: Take a look at the bowstring’s loops and ensure they are seated fully and properly onto the grooves. Step 4: Start lowering your compound bow until you see the limbs get back to the default position. The teardrop fittings are found on both ends of the bow’s cable. Then, use the other hand to put the replacement bowstring’s end loops on the teardrop fittings of the new string’s open sides. Use your hands to pull up on your bow’s riser and keep pulling to allow the bow attain a “full draw” position. ![]() Step 2: Use both feet to step on top of the bow string. Turn the bolts one after the other anti-clockwise, make three full revolutions so that a good part of the pressure will be taken off the limbs. The limbs of your bow connect to the riser at the limb bolts. Step 1: Locate the limb bolts of your bow and insert an Allen wrench right into them. So, whether it is a crossbow or other types, you can replace the worn string by hand.It may surprise you to know that you can do a great job restringing your bow, just like the professional archery shops. The truth is, you can replace your bow’s string without a press. However, you don’t have to always rely on the professional shops to restring your archery weapon. No doubts, archery shops have great tools such as the bow press that helps in relieving tension and restringing the bow. Restringing A Compound Bow By Hand – Step-by-Step Guide The reason is, shooting with a bow that has damaged cable or string can result in safety issues such as damaging the bow itself, or worse still risking the life of the shooter or even someone standing by if the string snaps without warning. Why Restring A Compound Bow?Īs mentioned earlier, once the compound bow string has lost strength and becomes worn out, it is very essential to have it re-stringed as soon as possible before even using the bow again. The appealing properties of a bow string will include strength, lightweight, resistance to water, and resistance to abrasion. As a result, they tend to lose tension with the passage of time. ![]() Majority of the present-day bow strings are built with non-stretching man-made materials. The compound bow string joins the bow stave’s two ends and works to launch the arrow.
0 Comments
Leave a Reply. |